Trade Tariff Heading: 8501
Electric motors and generators (excluding generating sets)
| Commodity |
Description |
Duty Rate |
Status |
Save |
| 8501522010 |
For use in civil aircraft |
0.00 % |
Exists in SQL |
|
| 8501522050 |
Ac synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,with:
- an output of 340w or more but not more than 7.4kw,
- a flange of dimensions of not more than 180mm × 180mm, and
- a length from flange to extreme end of resolver of not more than 271mm |
0.00 % |
Exists in SQL |
|
| 8501522070 |
Automotive-ready brushless permanently excited magnet synchronous alternating current motor with:
-a specified speed of not more than 7000 rpm,
-an output of 750 w or more but not more than 1.8 kw (at 12 v),
-a flange diameter of 80 mm or more, but not more than 200 mm,
-a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end,
-a housing length of not more than 265 mm, measured from the flange to the outer end,
-a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with o-ring and protective grease or liquid seal interface),
-a stator with single t-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets,
-whether or not with electronic power steering controller,
-whether or not with pulley or coupling,
-whether or not with rotor position sensor
|
0.00 % |
Exists in SQL |
|
| 8501522080 |
Electric permanent magnet synchronous motor with:
-an output power of 850 w,
-a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per gb/t 13560 standard) enclosed in polyethylene cover,
-an outer diameter of motor magnet shaft end with dimension of 10.001 mm or more but no more than 10.007 mm,
-terminals located across the radius 26.2 mm and separated by an angle 30.0°,
-a housing made of adc12 or ac46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per jis h5302 or en1706 standard) and anodised coating (per astm b580 type e standard),
-a back electromotive force constant (ke) of 0.04009 v-sec/rad or more but no more than 0.04431 v-sec/rad,
-a back electromotive force harmonic order - 5th of no more than 0.36% (of fundamental) and 7th of no more than 0.24% (of fundamental),
-a cogging torque of no more than 20 mnm,
-a friction torque in ambient temperature of no more than 26.5 mnm,
-a maximum temperature of motor operation of no more than 200 °c
|
0.00 % |
Exists in SQL |
|
| 8501522089 |
Other |
0.00 % |
Exists in SQL |
|
| 8501523010 |
For use in civil aircraft |
0.00 % |
Exists in SQL |
|
| 8501523090 |
Other |
0.00 % |
Exists in SQL |
|
| 8501529010 |
For use in civil aircraft |
0.00 % |
Exists in SQL |
|
| 8501529090 |
Other |
0.00 % |
Exists in SQL |
|
No match found for 8501101030 so setting active to 0 !!!
No match found for 8501109980 so setting active to 0 !!!
No match found for 8501200040 so setting active to 0 !!!
No match found for 8501510060 so setting active to 0 !!!
No match found for 8501522060 so setting active to 0 !!!
API source
